Universal control unit with integrated radio and infrared receiver. The control unit can be used as a manual wall switch for controlling screens, projector lifts, roller shutters and other devices with a 220Vac drive or optionally as a receiver for a radio or infrared remote control for wireless operation of the connected devices. A maximum of 20 handheld transmitters can be paired with one control unit. The buttons for manual operation (Up, Stop, Down) are located on the side of the box. The input voltage is 220-240Vac 50Hz, the control is connected between the power supply and the consumer. Optional:Handheld transmitter (radio), max. 20 supportedHandheld transmitter (infrared), max. 20 supported

The Projection Screen Trigger PRO is plugged in between the projector's power supply and uses the voltage increase when the projector is switched on and the voltage drop when it is switched off to send the radio command to open or close the motorized screen.This solution is compatible with our motorized screen series PRO 16:9 and PRO 1:1

In conjunction with a compatible receiver unit, the wireless trigger UNIVERSAL can be used to control the screen using all projectors that do not have a trigger output (DC Out).The wireless trigger is plugged into the projector's power supply. When the projector is switched on or off, it sends a corresponding signal to the remote control unit UNIVERSAL, which is installed between the power supply of the screen, a ceiling lift, or similar devices. This ensures that the screen or ceiling lift extends or retracts automatically when the projector is turned on or off. A combination of multiple components, e.g., a screen and an electric ceiling lift, is also possible. This allows you to automatically control the screen and ceiling lift at the touch of a button (ON/OFF) using the projector's remote control. IMPORTANT: The UNIVERSAL wireless trigger also requires the UNIVERSAL remote control unit as a counterpart and is not compatible with screens from our range that are already equipped with an integrated receiver and remote control.

Rechargeable radio remote control for the motor screen series PRO and CONTRAST. For initial operation, the remote control must be paired with the screen (please see instructions). The hand-held transmitter for the screen is supplied with a wall bracket.

Remote control for the LUSSO motorized screen. The early models of the LUSSO screen series were delivered with infrared-based remote controls. Later models were equipped with a dual receiver that supports both radio (handheld transmitter model SM128) and infrared (handheld transmitter model SM118). When replacing the remote control, be sure to check the model name on the back of the transmitter. The handheld transmitter is delivered together with a practical wall bracket.

Make your home theater even more comfortable. Make the remote control for your electric screen redundant. Your projector will take control of your screen - with immediate effect and without any cables or set-up work.Simply plug the newly developed projector screen trigger LUSSO into the trigger output of the projector and the screen will drop and raise itself when the projector is switched on or off - as if by magic.This trigger is exclusively compatible with our product series LUSSO.

Manual hand switch for the current series of VISIVO PRO motorized screens. The switch can be plugged into the RS485 socket on the right side of the screen casing above the power supply in order to operate the screen manually using a cable.

The screen bracket PRO is used for wall and ceiling mounting of the PRO and CONTRAST screen series from VISIVO. The distance to the wall is 20 mm and to the ceiling 15 mm. Packaging unit: 2 pieces.Important: The mounting bracket has been modified and is not compatible with older series of the above-mentioned screen models. If in doubt, send us a profile photo of your screen housing and we will check compatibility before ordering.

Electric ceiling lift COPERTO for suspended or standing projector installation, featuring a low installation height of just 12 cm. The ability to adjust the minimum and maximum stop positions allows even taller projectors to be easily positioned within the projector lift. This makes it suitable for concealed installation, for example, in a living area where a projector would be more of a nuisance on the living room ceiling on days when home theater isn't being used. The dimensions allow even a large home theater projector to be mounted upright in the lift or suspended from the lift base plate. The lifting range (maximum 96 cm) can be adjusted directly on the powerful tubular motor using the upper and lower stop points. The ceiling lift is delivered ready for use with a wireless remote control, wall switch, and 220V Schuko plug.

The height of this mobile projection table VARIO can be adjusted between 40 and 140 cm. Fine adjustments are made using a small hand crank located under the support surface, which measures 40 x 30 cm (width x depth).Thanks to its tripod base, the projector table is very stable. After use, the tripod can be folded down to a small, compact size and stored in a carrying bag. Due to its lightweight aluminum construction, the total weight, including the support surface, is only 2.5 kg.

Visualiser bag for OPTOMA DC550 and DC 554 Bag is empty and does not include the visualiser.

The projector mount SPIDER is a classic among ceiling mounts. Whether you need a fixed or variable ceiling distance, this ceiling-mounted projector bracket is compatible with almost all projectors thanks to its adjustable arms with a hole spacing of up to 350 mm. The ceiling distance without the extension is approximately 13 cm and by using the optional extension (included), a variable ceiling distance between 42 and 65 cm is possible. The signal cable can be routed through the extension, screws for projector mounting are included. The bracket is available in white.